Thursday, December 30, 2010
Question No.1 Marks-15 (5x3)

Consider the FA 1 and FA2 given below,
















Figure 1- FA1 and FA2

Using the FA’s listed in Figure 1

I. Build an NFA corresponding FA1U FA2 (Union)

II. Build an NFA corresponding FA1 FA2 (Concatenation)

III. Build an NFA corresponding to closure of FA2

Question No.2 Marks-5

Consider the following Moore Machine and build the equivalent Mealy Machine as well as determine the output of both Moore and Mealy Machines by running the string “aaabaaba”.









Figure 2- Moore Machine











ENG301 assignment no 3 fall 2010 solution

Objective

To assess the students’ ability to write business messages.

Instructions:

  1. No assignment will be accepted via e-mail after the due date.

  1. Plagiarism will NOT be tolerated. Plagiarism occurs when a student uses work done by someone else without acknowledging the actual author. It also means copying and pasting the material from handouts and internet source without rephrasing it in his/her own words.

Q1. As a reservation manager of a hotel, write a letter to your customer reminding

him that deposit is due on a reservation made for an executive suite. (10)

Q2. Complete the following statements with the correct answers related to Business

Communication. (5)

1. ----------- is the reply to a claim letter.

2. Letters written to persuade the people for purchasing your product are called -----.

3. -------- is a special committee which is assigned the duty to resolve a specific

problem.

4. A sales letter begins with --------------.

5. ------------ of an organization is followed in order to write a ------------.

ENG301 assignment no 3 Solution

CS408 assignment no 3 fall 2010 solution

Suppose, if you were to developing a new room for your house, the following specific activities you would expect to be undertaken and the following representations you would expect to be produced.














A: Initiation: You would initiate the system by deciding that you wanted a room, and produce the application description that broadly described what you wanted. This may be expressed in a letter, sketch or verbally and would form the basis of discussions with experts such as builders and architects.

B: Analysis of requirements gathering: You would produce a requirements specification detailing what the room was for (for example, a kitchen, a lounge, a bedroom), the amount of money available, how large it was to be and so on. This requirements specification thus describes the purpose the uses and the constraints that apply to your room. It would probably be produced in consultation with a builder or an architect and expressed in terms of sketches and a natural language description.

C: Design: An architect would produce a set of blueprints (a detailed, formal system design) which represented you requirements.

D: Implementation: A builder would use the blue prints to build the design and produce your room.

E: Operation and Management: During the lifetime of the room, you might change its purpose (for example, a bedroom becomes a study room) and you would certainly have to maintain it by repainting and so on.

F: Validation, Verification and testing: During these processes you would be checking that the developing product met you requirements (Validation) and was being developed in accordance with the plans (verification). You would also test parts of the product (for example that a window was at the correct height).

Question:

Using the information regarding developing a new room for your house discussed above, now write down a situation where you would start the development process with

a) A conceptual design.

b) A Physical Design.

How might the development continue in each case? [20]

Note:

o Assignment should be in your own wordings not copied from net, handouts or books.

o Your answer should be “to the point” and not more than 5 lines.

Solution can be found on

cs408 assignment no 3 solution vuhelp.net

CS101 Introduction to Computing Assignment No 3 solution fall 2010

You are required to Design HTML layout, validate form fields and manage fields style with the help of JavaScript. (20 Marks)

Layout







2. Validate Empty Field

If user will submit form without entering any value in GPA. Display warning message.

Change field background color to pink.

On clicking ok reset layout to initial state (White background, pointer focus on GPA field).












3. Validate Alphabetic Value

If user will submit form with alphabetic value. Display warning message.

Change field background color to red.

On clicking ok reset layout to initial state (White background, pointer focus on GPA field).












4 Validate Range of Value

If user will submit form with value less than 1 and greater than 4. Display warning message.

Change field background color to light sky blue.

On clicking ok reset layout to initial state (White background, pointer focus on GPA field).











5. Validate Correct Numeric Value

If user will submit form with value > = 1 and < style="mso-bidi-font-weight:normal">Fair :: You got D grade”.

If user will submit form with value > = 2 and < style="mso-bidi-font-weight:normal">Good :: You got C grade”.

If user will submit form with value > = 3 and < style="mso-bidi-font-weight:normal">Very Good :: You got B grade ”.

If user will submit form with value equal to 4. Display message “Excellent :: You got A grade ”.

Change field background color to lime.













6. Validate Find Grades Button

If value is > = 1 and <= 4, on clicking ok jump to www. vu.edu.pk

For any other value or empty field must not jump to www. vu.edu.pk

Hints:

1. For pink color use keyword pink.

2. For red color use keyword red.

3. For light sky blue color use keyword lightskyblue.

4. For lime color use keyword lime.

5. To change field background color use backgroundColor property of style sheet in JavaScript.

6. To set pointer focus on GPA field use JavaScript function focus.


cs101 assignment no 3 solution fall 2010

FINANCIAL ACCOUNTING 1 MGT101 Assignment No 2 solution fall 2010

Assignment No. 02 Marks: 20
QUESTION – 01
The following are the information available from the Trial Balance of Mr. Ali & Sons for the
year ended on 31st December 2010.
Adjustments:
� Write off Rs. 5,000 bad debts from accounts receivable.
� Maintain provision for doubtful debts at 5%.
Required:
1. Calculate new provision.
2. Calculate the amount of Provision for doubtful debts to be appeared in Profit and
Loss Account.
3. Calculate the amount of Sundry debtors to be shown in Balance Sheet.
QUESTION – 02
The financial year of Mr. Ali & Sons is closed on June 30, 2010. Data regarding Mr. Ali &
Sons is given below:
Required:
Prepare Debtors control account for the month of June, 2010.
Particulars Debit
Rs.
Credit
Rs.
Accounts receivable
Bad debts
Provision for doubtful debts
205,000
8,000
6,000
Particulars Rs.
Opening balance of sundry debtors 25,000
Cash sales 100,000
Credit sales 50,000
Discount allowed 2,000
Discount received 6,000
Receipts from debtors 35,000
Bad debts written off 10,000
Sales returns (from credit sales) 5,000

CS504 Assignment 3 solution fall 2010

Please carefully read the following instructions before attempting the assignment.

Rules for Marking

It should be clear that your assignment would not get any credit if:

  • The assignment is submitted after due date.
  • The submitted assignment does not open or file is corrupt.
  • The assignment is copied. Note that strict action would be taken if the submitted assignment is copied from any other student. Both students will be punished severely.

1) You should concern recommended books to clarify your concepts as handouts are not sufficient.

2) You are supposed to submit your assignment in .doc format. Any other formats like scan images, PDF, Zip, rar, bmp, docx etc will not be accepted

3) You are advised to upload your assignment at least two days before Due date.

4) This assignment file comprises of Two (2) pages.

Important Note:

Assignment comprises of 20 Marks. Note that no assignment will be accepted after due date via email in any case (whether it is the case of load shedding or emergency electric failure or internet malfunctioning etc.). Hence, refrain from uploading assignment in the last hour of the deadline, and try to upload Solutions at least 02 days before the deadline to avoid inconvenience later on.


Question No. 1

1) What makes a “GOOD” software architecture” [Marks 8]

2) Are architectures influenced by background and experience of software architects? Explain. [Marks 8]

Question No. 2

“N-tier application architecture provides a model for developers to create a flexible and reusable application”, Comment (5 to 10 lines). [Marks 4]

CS504 Software Engineering-1 Assignment 3 solution fall 2010

Object Oriented Programming (CS304) Assignment No.03

Deadline

Your assignment must be uploaded before or on 4tht January, 2011

Rules for Making

It should be clear that your assignment will not get any credit if:

o The assignment is submitted after due date

o The assignment is copied

Objectives

This assignment has been designed so that you would be able to implement the concept of composition in OOP. After the completion of this assignment you should have a good grasp on how to

o Inheritance

o Public & private inheritance

o Using basic constructs of OOP in a program

Assignment

You have to write a C++ Program in which you will have to write a class ‘Pakistani Citizens’ which has five data members “name, age, CNIC No, province, and domicile” and two data functions getter and setter for each data member e.g setAge() getAge() etc.

Write a second class ‘VotersList’ which inherited the ‘PakistaniCitizens’ class and has “implemented in term of” relationship to pakistaniCitizens.

The ‘VotersList’ class restrict the functionality of setAge() function by override the setAge() function of ‘PakistaniCitizens’ class and check the condition :

If age is greater than 18 then print “Eligible for vote cast”.

If object of VotersList class is initialized with the age less than 18, then it prints a message

Age is less than 18” and sets the value of age to default.


Cs304 assignment no 3 solution

CS302- Digital Logic Design Assignment # 3 FALL 2010

Due Date

Your assignment must be uploaded before or on 06th Jan 2011.

Upload Instructions

Please view the document related to assignment submission process provided to you by the Virtual University to upload the assignment.

Rules for Marking

Kindly note that your assignment will NOT be graded if:

§ It is submitted after due date

§ The file you uploaded does not open

§ The file you uploaded is copied from someone else

§ It is in the format other than .doc

Objective

This assignment has been designed to enable you to understand the concepts of:

§ Logic gates

§ Flip-flops

§ Latches

Assignment

Question_1: [marks: 14]

The following serial data are applied to the flip-flop through the AND gates as indicated in figure below. Determine the resulting serial data that appear on the Q output. There is one clock pulse for each bit time. Assume that Q is initially 0 and that and are HIGH.

Rightmost bits are applied first.

J1: 1011110

J2: 0101111

J3: 0111110

K1: 1100110

K2: 0101110

K3: 1101110

Question_2: [marks: 6]

Provide to-the-point (max 4 to 5 lines) answer to the following:

  • What is the main difference between a gated S-R latch and an edge-triggered S-R flip-flop?
  • How many flip-flops are required to produce a divide-by-32 device?
Solution of this assignment can be found on
CS302- Digital Logic Design Assignment # 3

CS401- Computer Architecture and Assembly Language Programming Assignment # 3 Fall 2010

Assignment

Question No.1 Marks: 10

Differentiate Synchronous and Asynchronous interrupts. Just give 2 to 3 differences also provide 1 to 2 examples.

Note: - Your answer must be to the point and in the bullets form otherwise your marks will be deducted.

Question No.2 Marks: 10

Read the following lines of code. It will read the mask register from port 0x21 and then set the 1st bit in the register. As soon as it is written back to port 0x21; IRQ 0 which is derived by a timer device will be disabled.

in al, 0x21 ; read interrupt mask register

or al, 1 ; set bit to disable IRQ 0

out 0x21, al ; write back mask register

Take out line 2 i.e.

or al, 1

Modify it to solve the following parts

1. Set bit to disable IRQ5

2. Set bit to disable IRQ4

3. Set bit to disable IRQ7

4. Set bit to disable IRQ3

5. Enable IRQ5, IRQ4, IRQ3, IRQ7.

Solution of this assignment can be found on

CS401- Computer Architecture and Assembly Language Programming Assignment # 3


CS 610 Computer Networks Assignment # 03 Fall 2010

Your assignment must be uploaded / submitted before or on January 5, 2011
Upload Instructions
Please view the assignment submission process document provided to you by the
Virtual University.
Rules for Marking
Please note that your assignment will not be graded if:
• It is submitted after due date
• The file you uploaded does not open
• The file you uploaded is copied from someone else or from internet
• It is in some format other than .doc
Objective
The assignment has been designed to enable you to develop the:
• Understanding about routing algorithms
Note: Material that is an exact copy from handouts or internet would be graded
zero marks. Your solution should consist of the material found through different
sources and written in your own words.
Assignment Statements:
a). Summarize the difference between classful IP address and classless IP
address in tabular format.
(Your answer should not increase more than one page)
(10 marks)
b.) Show your IP address by using DOS command “ipconfig” and answer the
following. (2 x 5 marks)
(i) Show your IP address and subnet mask
(ii) Convert the IP address and Subnet mask into binary representation.
(iii) What is the class of your IP address in classful scheme and why?
(iv) Find your host number and network number in classful and classless
scheme, also gives the reason to your answers.
(v) Given the address 23.56.7.91, find the beginning address i.e.
network address

CS 610 Computer Networks Assignment # 03 Fall 2010
Wednesday, December 29, 2010

cs601 assignment no 3 solution fall 2010 5 Jan, 2011

Question 1: [10]
Compare and contrast Twisted pair cable, coaxial cable and optical fiber with respect to
Property of Media, Cost and Bandwidth associated with each? Also discuss the
appropriate application of each.
Question 2: [5]
What are the categories newer than CAT5 of Twisted pair cable? What are the
specification and application of these?

cs601 assignment no 3 solution

Computer Proficiency License (CS 001) assignment no 3 fall 2010

Objectives

This assignment is designed to motivate students towards research.

Assignment

Q1. (a) What is difference between “Work Book” and “Work Sheet” in MS Excel?

(b) By default, how many work sheets are present in MS Excel file? 5 marks (2+3)

Q2. How can we insert pictures in MS Word document? 5 marks

Q3. Create a table in MS Word with 3 columns and 4 rows. 5 marks

Solution Computer Proficiency License (CS 001)


ENG001 - Elementary English GDB fall 2010 solution

Graded Discussion Board (Fall 2010) Graded Discussion Board for Elementary English (eng001) will be opened on 29th December, 2010 and will remain open till 30th December, 2010.
The topic for GDB is: “Be slow of tongue and quick of eye.” Explain with reasons.”
Read the following instructions carefully before posting your comments: 1.Write your own views about the topic. 2.Your comments should NOT exceed 100 words. 3.GDB carries 5% weightage in your final assessment. 4.Your comments should be clear, concise, and relevant to the topic. 5.Do not post your comments on the regular MDB even if it is open. Any discussion of the topic for GDB on the regular MDB will affect your marks in the GDB. 6.Any questions or queries regarding the topic may be asked through the email address eng001@vu.edu.pk. 7.Do not send your comments via e-mail. 8.Do not send your comments twice. 9.No marks will be awarded for plagiarism.

Solution of
ENG001 - Elementary English

eng201 assignment no 3 solution fall 2010

Business and Technical English (ENG201)
Fall 2010


Assignment # 3
Total Marks: 15
Due Date: January 4, 2011
Lectures: 23-29

Objective:
To assess students’ understanding of the course and to prepare them for practical application of communication skills through writing practices.

Instructions:

Late assignments will not be accepted.
If the file is corrupt or problematic, it will be marked zero.
Plagiarism will never be tolerated. Plagiarism occurs when a student uses work done by someone else as if it was his or her own; however, taking the ideas from different sources and to express it in your own words will be encouraged.
No assignment will be accepted via e-mail.
The file should be in Word doc form; the font color should be preferably black and font size can be 12 Times New Roman.


Question No.1 (10)

To provide the customers with the best beverages, the management of PC Hotel wants to sign a contract with the Juice Plus company. Being the supervisor of Food & Beverages Department, you have been asked to write a feasibility report for this purpose. Draft your report with recommendations.

Question No.2 (5)

‘Philips Lighting Company’ wants to conduct a survey on the use of energy savers in Iqbal Town Lahore. Write down at least FIVE methods of obtaining facts with detail for the empirical report.

Download the solution of eng201 assignment no 3

mcm515 assignment no 2 solution fall 2010

a) Listen to a radio program based on interview. Then give critical analysis
of that program highlighting the following: (10 marks)
1. Radio Channel name.
2. Program name.
3. Interview type.
4. Frequency of program.
b) You are suppose to produce an interview program on current affairs
keeping “Drone attacks scenario in Pakistan” in view, write at least 10
questions for the interview and prepare a list of possible personalities which
can be interviewed for the program.
(10 marks)
Guidelines:
 Critical analysis requires logical arguments, examples and proofs to
support your stance. Be critical and logical in the light of what you
have listened.
 Also check the schedule of programs of radio channels to have an idea
of what other programs are being on aired by this audio channel
during whole week.
 You can consult news papers, magazines or Google website to have a
theoretical knowledge for the Drone attack scenario in Pakistan.
Download the solution on the following link
MCM515
Tuesday, December 28, 2010

CS410 assignment no 3 solution fall 2010

Visual Programming (CS410)

Assignment

Total marks = 20

Deadline Date = 03-01-2011

Please carefully read the following instructions before attempting the assignment.

Rules for Marking

It should be clear that your assignment would not get any credit if:

  • The assignment is submitted after due date.
  • The submitted assignment does not open or file corrupt.
  • The assignment is copied. Note that strict action would be taken if the submitted assignment is copied from any other student. Both students will be punished severely.

1) You should concern recommended books to clarify your concepts as handouts are not sufficient.

2) You are advised to upload your assignment at least two days before Due date.

3) Send the complete source code containing all the project files in zip format.

Important Note: Assignment comprises of one question. Note that no assignment will be accepted after due date via email in any case (whether it is the case of load shedding or emergency electric failure or internet malfunctioning etc.). Hence, refrain from uploading assignment in the last hour of the deadline, and try to upload Solution at least 02 (two) days before the assignment to avoid inconvenience later on.

For any query please contact: CS410@vu.edu.pk


Question [Marks 20]

Attached with this assignment file is a zipped folder with the name “Realease”. Both “.Zip” and “.Rar” versions are attached, you are required to execute this project and develop a similar application.

HINTS:

The folder contains the executable of a counter application that, have a menu. The menu contains the items “File” and “Timer”.

“File” menu contains a single submenu item with the name “Exit”.

“Timer” menu contains two submenu items with the names “Start” and “Stop”

By clicking the “Exit” menu, the application will exit.

By clicking on “Start” menu the counter starts, and clicking the “Stop” menu, the counter will be stopped.

Also note that accelerators are attached with each menu item.

A similar application has been developed in chapter 18 of the handouts; you can get help from it.

NOTE:

You are required to develop a similar application from scratch and send the complete folder in zipped format containing all the project files. The project will be executed and marks will be awarded to applications fulfilling the above requirements, so make sure that you send the complete project folder and no single file is missing that may cause the project, not to run, in which case Zero marks will be awarded.


Cs401 Solution link

cs506 assignment no 3 solution December fall 2010

Answer the following questions keep your answers brief.

1) What are the requirements to run a web server? Write down all hardware and Software requirements. [3 Marks]

2) Write down advantages of layered approach for web development. [3.5 Marks]

3) Are there any disadvantages of layered approach in web based applications? [3.5 Marks]


Download the assignment solution on the given link

Downloading cs506 assignment no3

cs403 database assignment no 3 solution fall 2010

Q 1: Normalize the below table up to 3rd normal form.(7.5+7.5)

Student-ID

Specialization

Name

Specialization Semester

Semester

Start-Date

Semester

End-Date

Specialization

Supervisor

Vu001

SE

Faizan

Fall2009

05-07-09

31-12-09

Prof Majid

Vu001

AI

Faizan

Spring2010

05-02-10

30-06-10

Prof Saeed

Vu002

AI

Zafar

Spring2010

05-02-10

30-06-10

Prof Saeed

Vu003

SE

Ahmad

Fall2009

05-07-09

31-12-09

Prof Majid

Vu003

Networks

Ahmad

Spring2010

05-02-10

30-06-10

Prof Wajid

Vu003

AI

Ahmad

Fall2010

05-07-10

31-12-10

Prof Saeed

Vu004

SE

Fahad

Fall2010

05-07-10

31-12-10

Prof Majid

Vu004

AI

Fahad

Spring2011

05-02-11

30-06-11

Prof Saeed

Final solution can be found on this given link

Download solutution|

Vugurus. Powered by Blogger.

Popular Posts

Blog Archive

Labels

Imp Links

Followers

Total Pageviews

Subscribe for email

Blog Archive

Labels

Search

Loading...

About Me